This article says which you can make a plasticine ship, and how to make a military boat to children. Attention is paid to how to make a pirate ship with their own hands in stages. The step-by-step model of the sailboat is also characterized.
How to make a pirate frigate?
Romance of traveling for distant seas and mysterious countries is accompanied by many centuries. And this child interest should be used for complete. The manufacture of the frigate of the pirate fleet by modeling is very exciting, and the result is worth it. Such an exercise can be especially interesting for those who are tired of sculpting monotonous figures and cars. Frigate is usually prepared from plasticine brown and black colors.
Even the blue is not always needed, because instead you can use white material. The dark mass is required to be broken in the hands. Then, between its palms, it is pulled in length.
The edges of the details must already be than its middle part.
The following steps, allowing step-by-step to make frigate, are:
- Formation of cakes similar to the contour on the fish;
- Arrangement of the housing of 3 or 4 "sausages" of brown material;
- creating a bottom of plasticine cakes;
- Fastening to it at an angle of 90 degrees of additional oval cakes;
- Fastening long strips, which enhance the edge of the bottom;
- fixation of the dark mass on the nose of the future thunderstorms of the seas;
- Design from a blue or white material of 1-2 sails;
- Fastening the rod handle or an unnecessary pencil, for which (to create an almost full-fledged mast similarity) to roll brown pieces;
- compound mast with sails;
- Adding a third mast for a more complete imitation of the real frigate;
- Installation on the highest of the mast of the Black Flag (or the Red Flag, or any flag of the great naval powers of that time: the pirates used them all);
- Attachment to one of the armature sides (plasticine yellow color).
How to make a warship?
Despite all the fascination of pirated themes, floating models of modern and historical vessels of various military fleets may be no less interesting. It is not easy to cut them out, because the detailing will be much greater than in the previous case. But already there is already a faithful help: real photographs of certain warships. To cut the warship in stages, you will need:
- match;
- stack;
- Black, blue, gray, yellow and red plasticine.
The main role will play gray plasticine. It is from it that makes the main part of the hull and a flat deck. Warming Mass Hands will not need. Finished bar pressed with fingers from two edges. Waiting for the warm-up of plasticine, pull sharp edges from two sides.
If there is no desire to wait, simply cut off the mass, demonstrating the configuration of the shuttle.
The following steps are:
- from the remaining gray fragments are preparing a bar and a pair of round pellets;
- fasten these billets on the deck;
- connect the pellets among themselves;
- form missile blanks in the form of gray cylinders;
- gluing warheads (yellow);
- glue missiles on the nose of the ship;
- Another rocket is rear;
- Make a mast and flag for her (the principles are the same as the frigate).
Sailboat modeling with her own hands
But traveling romanticism for children is attractive even by itself. Many do not want to communicate with no military, nor with flibistra topics. An excellent choice in this case turns out a simple elegant sailboat. The housing is no longer made of gray, but from brown plasticine. He will again have to give a rectangular configuration and stretch the top.
The formation of sides, nose and feed should be neatly. Middle portions of the side will have to be cut. Good models of feed and nose are located above the center, as in real sailing fleets. Drawing the case of the body is facilitated by plastic knife. The gun ports are optional: for a peaceful sailboat they are not needed, therefore you can refuse them.
But the drawing of decks and stairs should be detailed. Masts form from wire. Important: The highest is placed in the center of the sailboat, and the lowest put on the stern. A slice of toothpicks putting on the nose symbolizes a bushprit. All masts are then equipped with sails. In order not to sculpt again, use paper.
The peaks of sails are covered with thin brown solutions. It is possible to retain sails by joining them with a small amount of plasticine from the inside. The dark blue thread will imitate cables. Such cables are wound on all masts. Nothing is more particularly required.
There are more recommendations:
- form round blue portholes;
- roll over massive plasticine parts on the boards using the rock;
- For the prevention of adhesion of the mass to use the food film;
- thoroughly align all the surfaces of the winged ships;
- If you wish, complement your ship figures of sailors, captains and passengers, cabins and rescue circles, boats and chimneys (if you are slammed).
About how to make a pirate ship from plasticine, see the next video.