Malachite plasticine box (28 photos): how to make the basis with your own hands? How to make the imitation of malachite on cardboard? What does a box look like after work?

The hostess of the copper mountain from the fairy tale of Bazhov gave Stepan a malachite casket. Since then, this thing is associated not just with a skillful work, but also with a miracle, a symbol of beauty and magic. You can make your own malachite casket with minimal spending. To do this, it is necessary to choose the material-imitation, with which the plasticine is perfectly coping with.

Tools and materials

Malachite pattern is arcs, loops, waves and divorces of all sorts of shades of green. It is easy to portray these color overflow watercolor, but the plasticine will give greater similarity with a valuable stone.

Tools that need:

• Stacks - a set of "knives", usually plastic - sharp, rounded, with embossed edges;
• The board - it will be necessary to not blur the table;
• Rock - need to roll out plasticine.

Materials for creating a box:

• A set of plasticine is the one in which the shades of green and close to it will be many colors;
• varnish - you can cover them the finished craft (if the varnish is taken, we need and brushes);
• The base that will be slapped with plasticine is a regular wooden blank under a casket or a plastic container (a method is described below. The method of manufacturing a round box of cardboard and bobbins from tape).

Sometimes the product is additionally decorated using beads, beads, buttons, braid. This is a question of an individual approach, the main thing, to make a qualitative basis, and whether it will need a decorative addition, secondary.

Instruction

If you want to fully make a malachite box yourself, that is, make it yourself and the foundation itself, you can use cardboard or similar solid material.

The foundation

Make "from scratch" optional. You can turn a gift box or just a box from the technique (mobile phone, hair dryer, etc.) into the malachite casket. An interesting option is a round casket, which is based on a bobbin from Scotch. Binding cardboard will also need.

Consider how to make a round billet box.

1. Bobbin is applied to the cardboard and draw 3 circles on the inner and two circles along the outer diameter.
2. The circumference, the diameter of which is smaller, should be glued together. It is easier to do this using the glue "moment".
3. The finished element is necessarily processed by the sandpaper, it glues with a circle of larger, adding to the center. So the cover is formed for hermetic closure of the container.
4. The edges can also be handled by sandpaper.

This is a layout of the caskets, it needs to be decorated. Decoration options are very much, but in this case plasticine will be used.

Imitation material

It comes the most responsible moment - you need to work with the plasticine so that it becomes as close as possible to this Malachit.

Work with plasticine includes several stages.

1. Primary colors, which will allow you to imitate malachite, green, white and black. You can use all kinds of green variations, go to blue shades, in a word, experiment. From each shelter of the selected plasticine to be cut off a small fragment. Cutting plastic mass is easier to stack.
2. On the cut pieces you need to put a sheet of paper and roll them. For this purpose, the rod is also suitable if it is. Very often the rolling pin is found in children's sets for modeling.
3. It turned out to be rolled plasticine plasticine of different colors. Now they need to be folded on each other, as if forming a well. The stack of formations must be collapsed by the tube.
4. Now from the rolled tube will have to Make a bar . To do this, first it must be surpassed from above, then turn over and press again.
5. The resulting multicolored bar should Cut on sufficiently thin plates. So it turns out the malachite, which the casket will be bold.
6. If you use three colors of plasticine, respectively, the pattern will be tricolor . The more shades are used, the harder the pattern is obtained. At the same time, the layers will have to roll thinner, otherwise it will not be possible to turn them into the tube, and then turn into a bar.
7. Someone initially adds glitter to plasticine (powder, sparkles of scattering), Wishing to make a casket shining. You can decorate it and so, this is the author's right.

The easiest and most reliable option is to glue the resulting plates (they will be square).

No need to smear anything, spread with your fingers . If you go more difficult, these fragments will have to be changed directly on the box, during baking.

Assembly

It is better and easier than the plate formed "malachite" attached to plastic. Therefore, the use of a plastic container is a health idea. This design can then be so wash, not afraid that the water will dwell all the base. If the casket is a cardboard, inside it can be made with green felt or velvet paper - so the handicraft will be even more close to the real box.

The assembly lies in the applied gluing of the formed "malachite" plates based on the basis. After the entire base was under the plasticine, it can be covered with a transparent varnish. So the drawing will be protected from the deformation and will serve longer.

If after the assembly it seems that the casket looks not enough, you can put the gold braid on its contour - it is fixed on the "moment" glue. You can create a small floral composition from other colors: to make a bright flower surrounded by gear light leaves and this composition fasten the center of the casket cover.

Recommendations

These tips will help complicate the work on the product, receiving a more spectacular option.

• "Malachite" can be made from a variety of colors. If you use professional plasticine, there are some shades of green, no less. Fragments of such strokes can be buried in one ball, it is he who will roll into a large layer. This layer is rapped by a wide rolling pin, it will turn out no less than a sheet of A4 format. Such a layer and you will need to have a billet.

• Think over the inside of the casket stands even before it is salabing. As already noted, it is possible to lay out the bottom and the walls can be felt, velvet paper, as well as atlas, patterned flannel cut, etc.

• For the box you can make a latch - it is easy to find in the fittings department . You can decorate the latch with a tassel. If a decorative cord is laced on the edges of the box, the brush on the lock will look like a final touch.

Successful creative experiments!

How to make a malachite box of plasticine, look next.