Lovers of modeling will be not interesting to learn how to make a phone from plasticine. Sometimes it is very useful to figure out how to make the city phone with children for the game. The modeling of a small mobile for dolls do it yourself, finally, also turns out to be a rather attractive occupation.
How to make a city phone?
Many children and even adolescents have no longer idea what the device looks like. At best, they saw it in graphics, in photos and in films. Therefore, the thought of making a small wired phone with your own hands with your own hands with a guarantee. Corps of telephone sets could greatly differ in geometry and colors. And yet, in most cases it was a "box" of a rectangular or square-shaped white or black.
In order not to suffer with the choice of color, prefers usually with a gray tone. 2/3 of the entire plasticine mass will go to the manufacture of a ball.
Next step by step:
press the ball to the board;
pressed on it immediately from 4 sides;
achieve the appearance of a four-grade pyramid of truncated type;
The residue of the gray mass is formulated in the form of thick sausages;
disintegrate her arcuate;
Due to the pages of the fingers achieve an external similarity with a simple handset;
prepare a white or blue dial;
add a small amount of gray mass in its middle;
Install the disk over the case;
squeeze the numbers of the empty rod from the ballpoint handles;
Instead of the lever put a couple of blue balls;
put the tube on the lever;
Connect a thin black cable between the handset and the body of the apparatus.
But many would like to get not gray, but a more pleasant red phone. It is not much difficult to do this - however, the algorithm is somewhat different. To start:
Cut 2/3 from the bright bar;
thoroughly knead this mass;
Rolling her on the ball's manner.
Such a blank must be flattened under a certain angle. Such a plane will become the face of the housing and support for the dial, so it needs to still give some angularity. Part of the manipulation is performed with a stack, part - with a knife and fingers. Ultimately it should be a place to attach the tube.
Next, you need a cap from a tube with glue or from the stationery marker. They create the outline of the future disk in a circle. From white plasticine, a circle of approximately suitable cross section is formed, stick to the surface and again watched the contour. It is not necessary to customize it in millimeters - you still almost certainly have to cut or add material. On the disk need to create recesses.
Next steps:
White plasticine mixing with black;
Attaching the gray sausage on top of the disk;
Installation in its center of black sill;
Preparation of levers from reddated plasticine;
formation of recesses for these levers;
Creating a dentitin that allows you to firmly fix the tube;
rolling out of orange strips, which is then gradually turning into the tube;
preparation at its ends of the holes;
Formation of a "telephone cable" from black plasticine;
Preparation of deepening under its mount;
Disk framing with a red stripe.
Mobile modeling
But for children are interesting and other communication devices more modern type. It is quite possible to imitate them for dolls.
As a basis, you can take one of the most "cool" telephones, which is only available today - iPhone 11. Especially since it will cost, it will be an order of magnitude less than its original pre-preparation.
- The case makes rectangular, light gray. But this is only the basis; Next, it is completely fascinated by a coal-black material, after which it will have to use saturated red plasticine. The same strip (initially operated on the "sausages") joins throughout the perimeter. The red material is modified a little, giving it a little relief in separate places.
- The next step is the preparation of not too thick gray square. It will indicate the panel located behind the smartphone. It is driven by a stack around the perimeter to get the most clear and expressive contour.
- There are 3 black germs on the surface of the panel. One of them - the camera - tested around the perimeter with a thin plasticine thread. Then the time will come to the design of the corporate symbol. Such an emblem is made of light gray stuccoing mass. Decoration placed strictly in the middle of the case. When it is delivered, it is possible to cut into the side of the smartphone to imitate connectors. After that, only minor modifications and Dorivovka will be needed. In the skillful hands of work will take quite a bit of time.
Useful advice
If the aircraft is planned as a gift, or it is collected for a long time to store, it is useful to cover the surface with a transparent varnish. Plasticine under it hardens and will become brighter, and cleaning will be significantly easier.
In the process of the phone modeling, it is necessary to periodically take breaks. Roll out the material with a kitchen rolling is much easier than hands or improvised fixtures.
If something does not work, it is better to suspend the work and return to it later than to be disappointed.
Place for modeling should be convenient and as highlighted.
The manufacture of a plasticine phone itself is available only to those who have already nubble in this hobby hand. It is necessary to master not only the formation of sausages and pancakes, but also more simple figures, compositions. At the disposal of fans of the modeling can be different stacks - and you need to try which tool it is individually suitable for a particular work. There are no more special subtleties and nuances.
How to make an iPhone of plasticine, look in the video.