Lady grinding: how to throw the frets with your own hands on the electric guitar and an acoustic guitar? Polishing tools

Landing strings on the guitar are the difficulty that will upset any person with hearing. Moreover, it may occur even on a recently purchased tool. Eliminate this problem will help grinding. And it is worth considering how to fulfill this procedure yourself.

When do guitar frequencies need grinding?

The reasons for the phenomenon are in several factors. First, from the production of budget models, the final grinding is often excluded. Without attracting specialists, it is possible to reduce the cost of the instrument, but in fact the savings are done on the quality of the sound.

Secondly, if the regions of production and sales of the guitar do not coincide, the tool is subjected to climate effects. Due to the temperature and humidity drops, the tree begins to dying, drinking moisture. As a result, the radius and height of the lands are changing.

Sometimes there is a human factor, including non-accuracy during transportation, the use of a set with a smaller caliber when changing strings. The uniformity of the location of the lands is also lost when wear.

What do you need?

Before work, you will need to evaluate the state of the tool. If the deviations from the norm are small, it makes sense in grinding. If there is a significant amplitude of the walking of the lands in the propils, they will have to loliden in order to achieve the desired fixation. At the same time, experienced masters recommend their full replacement. Considering that in cheap rod guitars are performed from soft alloys, this procedure is inevitable.

For grinding and polishing the instrument will be required:

• Malyary Scotch;
• ruler;
• marker;
• bar;
• Files;
• hammer;
• feet;
• sandpaper (1000, 1500, 2000);
• Polishing circle.

For grinding also use steel wool, grinding eye on a tissue basis. You can polish them after alignment and rounding.

Technology

Grinding of the lands on an acoustic guitar is made according to a specific algorithm.

1. At first, you will need to remove the strings and make a painting with a painted chest.
2. Then remove the deflection of anchor. On a flat hafe, it will be easier to estimate the unity of the height of the wards.
3. Now the long thick metal ruler goes to move. It should be put on the Lada and check its position. Ideally, the device will fall smoothly and reliable. If the ruler formed a deflection, it means one of the elements below the rest. And the outstretched man will lead to the fact that the line will be swollen on it.
4. Then the frets are painted with a marker. At this stage, they will be overwhelmed by perfectly smooth bars and sandpaper. It is important to maintain the uniformity of the press, moving from one edge of the Lada to another.
5. After a pair of passages, it is worth assessing the status of the marker markup. If color traces remained, it means that these sites were lower than the level of grinding. Then it is necessary to re-apply the marker on the surface and resting it so that the painted areas does not remain.
6. Performing adjustment, you need to take into account some nuances. So, the first way can be slightly higher than the rest. And starting from the 12th, the height is permissible to resolutely.
7. When the lads are found out from the groove, it is worth using the hammer and a storage.
8. After grinding, the threshings become flat. If they immediately pull the strings, then because of the larger area of ​​contact, they will vibrate worse. Therefore, now the edges of the profile need to round the supfil.
9. Now you should take care of the return of the lads of the former smoothness and gloss. This requires 3 passages with sandpaper. The first time you need grain 1000, then - 1500, and in conclusion - 2000.
10. The final stroke will be polished. For the procedure, a special circle is needed. Alternatively, the use of gay paste and soft vehicle is allowed. With these means to grasp the brilliance every way. In this case, items should not overheat. Otherwise, they will shift again with grooves.

Now you can wear strings, rebuild their height, the position of the grid and evaluate the result of the work. Grinding is well done if the strings began to clamp easier, chords sound without dissonant impurities, when tightening, there is a better slide strings in Ladam.

Useful advice

1. Before embarking on grinding, it is necessary to make sure that it is the cause of the ring and the pride. Sometimes the problem is to curvathes the griff, and it has to be decided otherwise.
2. When inspection, it is important to take into account the height of the thresholds. If they are too low for turning, it is better to replace them.
3. Do not overestimate your own strength. So, if we are talking about the restoration of the expensive guitar, and not about bringing the budget counterpart, it is better to trust a specialist. Otherwise, the attempt to save will turn large cash costs.

Let's summarize. The irregularities of the wards in height negatively affects the quality of the sound, which reduces the pleasure of the game. With this difficulty there are musicians who bought the tool recently, and owners of old guitars. When the irregularities are detected, their grinding and polishing are required. At least work and can be entrusted to the master, it is easy to level the frets on an acoustic, bass guitar or electric guitar with your own hands, observing simple instructions.

On the grinding of the lads of the guitar, see the video.