One of the most popular winter entertainment is a roller ridge on a tubing, which is more famous as "Watrushka". This device is made of durable reinforced fabric. However, it may be damaged, and this applies to both the outer cover and the rubberized chamber.
It is best to contact a specialized workshop in a similar situation, although sometimes you can try to take the "cheese" yourself at home.
Common problems
Some problems can be distinguished, which most often arise from the owners of tubing.
- Burnt camera . This happens when several people ride at the tubing at the same time, and at the same time their cumulative weight exceeds all permissible norms. Such damage also gives the pumping of the chamber in the cold. After it turns out to be warm, the air inside expands and it also causes a disruption of the integrity of the bottom.
- Cut . Such a trouble happens if users ride on an unprepared highway, as well as if a riding person in his pockets are sharp objects that can damage tubing in the riding process.
- A little less there are such damage as cable or handle . The cause of such a problem is excessive efforts, the worniness of the "Watrushka" or factory marriage.
- Sometimes on products Dissolve joints - It can happen due to factory marriage or with too strong inflats.
How to fuck?
Case
In case of damage to the case of tubing repair Works are manufactured in the following sequence:
- "Watrushka" must be put on a horizontal surface in such a way that it can be easily reached to internal damage;
- The damaged section of the cover is neatly rubbed in shallow emery paper;
- The piece of the truthes is wetted with acetone, then degreased and cleans the locations of damage;
- Next, it is necessary to measure the cut using the ruler;
- From the prepared material for a patch, a piece cut out so that it is a couple of centimeters more than the breakthrough size;
- All sharp corners on the prepared piping are cut off with scissors;
- the pay is degreased with acetone as well as the place of damage;
- Both surfaces to be fastened, linse with glue as evenly possible;
- Immediately before the hitch of bookmarks, both surfaces should warm the hairdryer, using hot air;
- The prepared patch is firmly pressed to the case and fixed by any press, after which they leave for 5-7 hours;
- After the reserved time, the press is removed and leave the cheese for another 15-20 hours - after that the maximum coupling strength will be achieved.
If the place of damage is small, then you can try Repair the rupture on the cover with the help of reinforced Scotch . In this case, the torn plot needs to be simply sewed, on top of the seam along the inner part, the piece of Scotch is fixed.
Camera
In order to fix the camera in tubing, The following materials and tools must be prepared:
- pelvis with warm water;
- scissors;
- Patchwork material;
- any solvent;
- small sandpaper;
- glue.
The sequence of actions step by step includes certain steps.
- First you need to determine where the puncture is located. For this, the product is thrown into the pump and placed in a large tank with water. If you do not have a pelvis, you can use the bathroom by filling it with half. In the place of the puncture will be noticeable air bubbles, rising upstairs.
- This plot should be marker.
- The place near the damage is shedding by sandpaper, then wipe with a cotton swath in the solvent. It is necessary in order to ensure the most strong fixation as possible.
- From the prepared material, the patch is cut out of the required size so that it is 1-2 cm wider than the parameters of the destruction itself.
- Before starting work, the camera must be launched.
- The glue is evenly distributed over the separation site and the patch, after which the latter is fixed on the camera with the press. In this state, the tubing is maintained within 2-3 hours until the final drying.
Maximum gluing efficiency is achieved after a day.
Elimination of other damage
In all other cases, such as, for example, fastening a torn cable or replacing damaged handles, special equipment will be required. Perform such work at home, without having the skills of work, the necessary tools and materials is impossible. In this case, it makes sense to attribute to tubing on a tire installation or in any service center, which is engaged in the repair of rubber products.
Keep in mind that in some cases the cost of repair may be comparable to the value of the new "Watrushka".
Those who firmly decided to make repair with their own hands, should special attention should be paid to the selection of adhesive composition.
Some funds are the greatest effectiveness.
- Texacol . Provides high quality gluing products made of polyurethane and polyvinyl chloride bases, most often included in the repair kit for the repair of rubber boats. In order to increase the heat resistance of this composition, a hardener is usually added.
- Liquid beam . It is a monocomponent composition containing special reagents capable of melting the outer layer of PVC coating. After cooling, such a patch is fixed tight to the surface of the tubing. Latca is presented in stores in an extensive color palette, so you can always choose the necessary tool.
We draw attention to the fact that it is possible to use the composition only if you repair small cuts and punctures whose value does not exceed 4-5 cm.
- For some types of damage use Reinforced Scotch "Moment Super Tape" . It provides fixation of a wide variety of materials, including the reinforced canvas. This tool is a three-layer product consisting of polyethylene, fabric, as well as the adhesive layer. It has high efficiency when sealing seams, joints, as well as insulation and protection of tubing from water penetration inside. It is noteworthy that this material withstands low temperatures and delays moisture, not even a strong direct flow of water.
Recommendations
In order to reduce the risk of Tubing damage, you should follow certain rules for skiing and operating.
- You can ride exclusively in specially designated places equipped with riding. Plots with trees and shrubs, pillars sticking with snags and other obstacles should be avoided.
- Do not clutch the Tubei with each other - It reduces maneuverability and as a result leads to damage in cases, if suddenly the tubing will face an obstacle.
- Do not sit on one "cheese" together . As a last resort, the use of one tubing for two people during riding on a slope canopy.
- When riding you need to hold onto the handles.
- It is not recommended to inflate tubing over the established norm. . Rightly inflated camera should simply reap the shell, but no more.
In addition, it is strictly forbidden to use Sanki-Vatrushki:
- in a state of narcotic and alcohol intoxication;
- for jumping from a springboard;
- For riding with iced or ski slopes.
Remember: any ice riding is not only unsafe, it also causes an accelerated wear of the sliding surface of the Tubing bottom.
It is not allowed to use the cheesecake to tow the snowmobile, car or any other vehicles. Also in the summer should not be attached to the boats and ride water.
About how to make a tubing case, see the next video.