Much popularity acquired interior items made by their own hands. With their work, there are all available primary materials and fixtures. Such a creative process requires a considerable amount of free time, but the result always exceeds the wait. We suggest you make candidates from newspaper tubes with their own hands.
Peculiarities
Weaving from paper vines have one big advantage. The paper has a much smaller weight than vine, and items from it are lighter.
Also paper vine is more elastic and able to withstand cooler bends What gives new opportunities when weaving.
Due to this, it became possible to manufacture minor products.
Products made of paper vine are obtained elegant and very beautiful.
With proper caller, they are very difficult to distinguish from the items made from the natural vine. Mostly in such a way, small items are made to decorate the interior.
They serve as an addition to the atmosphere of comfort and comfort in the house. Below is a master class on the manufacture of several pieces of paper vine.
Vine from newspaper tubes
First of all, it is necessary to prepare a paper vine. For beginners, consider step by step the manufacture of vines from newsprint.
In this process, the following materials and devices will be involved:
- paper or newspaper;
- Stationery knife;
- scissors;
- PVA glue;
- a small brush;
- knitting needles with a diameter of 2 mm;
- acrylic lacquer.
So, you need to take the newspaper and cut it along the fold line. On the resulting sheet, tick the band with a width of 7-8 cm, and fold it across. Cut on the fold line. There should be a strip 7-8 cm wide and about 30 cm long.
Put a sheet of paper on a flat solid surface. Take the knitting needle, put it on the edge of the prepared sheet of paper at an angle of 20-30 degrees. Holding the sheet of paper with one crayfish, the other we begin to wind it on the needle. Gently press the sheet to the needle so that the tube is sufficiently dense.
It is necessary to wind up the paper so that the ends of the tube are different diameters - one slightly more than the other.
It is necessary to build a paper vine. It will be inserted into the end with a smaller diameter to the end of another tube with a large diameter.
At the end of this process, there should be a small corner of paper, which must be lubricated with PVA glue and glue a paper tube-scattered on the needle. Carefully remove the paper vine from the needles and let dry the glue.
To make a candy man, you need about 50 such newspaper tubes.
Do not hurry in the manufacture of such a straw. The tubes should be dense enough so that the product is durable.
For the final readiness of the tube must be painted.
It is ideal for a water-based simulator.
The rich color palette allows you to easily choose the desired color. It is necessary to take a beam of a paper vine (15-20 pcs.) In one end, and others omit in the container with the veneer. Then take out, give a sort of sulfice of the veil from the tubes and turn over. Repeat the operation with a unwrapped end of a beam of a paper vine.
After the tubes are completely painted, they must be dried.
It is necessary to catch such a moment, the code of paper vine will be a little wet. It will give her better elasticity, which is important when weaving. If the paper vine dried finally and became solid and inflexible, then it is necessary to sprinkle it with water from the spray.
It is necessary to wet the middle part so that the ends of the vines remain solid.
Cup icon
As mentioned above, To create a cup of candlers, we will need a minimum of costs and materials. . This product is obtained very functional and practical. It really helps add an additional charm to the tea ceremony, comfort and the presence of something domestic and native.
Cup weaving begins with a bottom.
To do this, you need to take four pairs of paper vines and cross them crosswise in the center. In places of plexus, lubricate the plow glue. In the future, these tubes will be called guides.
Fold the next paper vine in half and put on the 4 guides. Gently press it towards the plexus center of the guides (middle of the bottom). The top half of the tube is lowered down and skip in four neighboring guides. The lower half raise up and spend on top of the neighboring 4 guides. And so alternate in a circle. This method of weaving is called a "rope".
As wept, paper vine will end. To increase the tube, it is necessary to drop PVA glue into a hole of a larger diameter and insert a new vine into it.
From the other end of the straw, it is necessary to do everything on the contrary - in a new vine drip glue and put it on the thin end of an ending tube. Loading 3-4 rows and disconnect pair guides. Now it is necessary to catch each guide.
When the desired diameter is reached, we leave 1.5 cm on the working vine, the rest is cut off. The remaining ends with the help of the needles hide in weaving.
So that our saucer looks finished, it is necessary to close the edge of the weaving.
We must take a guide, bend it towards the neighboring, make a bend on their intersection and, retreating 2 cm from it, cut off the residue. The resulting tail will be fed next to the adjacent guide. So do it with all guides in a circle.
Rubysko or a saucer is ready.
The weaving cups also begins with the installation of the guides.
We fold a paper vine in half and wake them from below through a saucer. We set them in such a way that the guide cups flies the guide saucer. Then bend one tube and put it on the guide cups. We start weaving similarly to weaving the bottom, only vertically.
After 3rd rows, you need to insert some kind of flipping form. It can be any utensils in the form of a hemisphere.
Guides must be evenly distributed, press to form and fix with clamps or clothespins at the edges.
The distance between the guides should not exceed 3 cm, otherwise weaving will be fragile. After reaching the desired height of the cup, finish weaving in the same way as when weaving a saucer.
To spare a handle, you will need 3 paper vines.
2 tubes put in parallel to each other. To one of them at a distance of 2 cm from the edge, we glue the third vine. Let dry. Insert between two tubes insert two needles for rigidity. The third vine is starting to be pulled out by eight tubes along with the knitting needles, retreating from the edge 2 cm.
We finish weaving also for 2 cm to the edge of the vine. We take out neat knitting needles, refuel the end of the third vine in weaving and slide glue slightly.
The knob woven braids is ready, it remains to attach it to the cup. To do this, with the help of the needles, the ends of the handle of 2 cm refuel into weaving at the top of the guide cup. Also enter both at the bottom. For stiffness, we lubricate these places with PVA glue. Let the cup dry finally.
To give the strength to our candlers, it is necessary to process to it.
For this, PVA glue to dilute water in proportion 1: 1 and applix a solution with a brush throughout the product.
Well dry and the mug is ready.
Vase
To weave the openwork vase for sweets, it will not take a long time. Start you need from weaving a bottom. After the bottom has reached its size, take 5 guides through one on one side, 5 - from the opposite side and raise them up. Fix them together at the top of the clip or clothesp. These are the workpiece under the future handle of the vase.
To perform openwork weaving, you need to take a steam guide and run it under the adjacent guide.
Then lift up the next guide, lower down to another and output. Must get a small semicircle.
So to do with all the guides. All the ends of the guides should go upstairs.
To give a shape, a vase must take a glass jar with a volume of one liter and put it on the bottom of the product.
Gently compress weaving around the can and flip upside down. The remaining ends of the guides of the three rows of weaving "rope" and finish weaving just like when making a cup of cups. This will be a vase stand.
We form a vase handle and wind up the top pieces with a paper vine. For strength, lubricate PVA glue.
Candle with a lid.
The manufacture of candlers with a lid is performed absolutely the same as in the case of previous products. First you need to weave the dyshko of the specified size and then get the guide upwards. Weaving "Rope" weaving the necessary height of the candlers and finish weaving.
In essence, the lid is the same donyshko, only with a small handle in the center, for a convenient opening.
Woven the cover with a diameter is slightly larger than the diameter of the candy.
How to make candidates from newspaper tubes, look in the video below.